Contents
A good-conditioned floor scrubber runs properly that scrubs and dry floors on in a single pass on the floors. No matter, what type of floor it is. It reduces costs and labor as well as requires fewer maintenances even after taking a heavy load on it. But, like any other same type of equipment so it can experience several issues that will lead them to be dead, break or stop working. So the users of these kinds of equipment look for advance floor scrubber troubleshooting to have a steady run for their scrubbers. 
The brittle equipment to perform a heavy-duty are frustrating. They are costly, time-consuming as well as very difficult to fix easily. Sometimes, for some issues of the automatic floor scrubbers are easy to fix by ourselves. So we can easily avoid fetching a professional expert for the simple issues. In this article of advance floor scrubber troubleshooting, you will understand the causes of problems. You also see the ways of troubleshooting to fix them in a shorten repair time and will help you cost to a minimum. The possible troubleshooting is listed below for your convenience.
- Scrubber Doesn’t Power On
- The System Doesn’t Release Water
- Brush Deck Doesn’t Scrub
- Poor Scrubbing Results
- Down Runtime
- Poor Dirty Water Suction Capability
Troubleshooting-1: Scrubber Doesn’t Power on
If you have an upright floor scrubber, it must be a cord-electric. And for a larger size above 24-inch is battery-powered. So this is easy to understand that if your scrubber is not running by power on, it is either not the machine plugged in or the battery is dead. 
For the cord-electric machine, check the plug if it hasn’t fallen out of the outlet. Or, the outlet of the cord may be faulty. If the machine is plugged, check the outlet to be firm whether it is good or faulty. Moreover, you can counter check by plugging another device into the same outlet. See if it getting sufficient power or fully dead. If the process doesn’t show evidence of power, it assumes the outlet is quite faulty. So get resetting the circuit breaker for the faulty wall outlet.
Furthermore, if it is seen the problem continues, make sure that the problem is not with the outlet. The power cord may have run out. It needs to be replaced immediately. So you can contact an expert to troubleshoot your battery-powered electric floor scrubber.
Troubleshooting-2: System Doesn’t Release Water
Advance floor scrubber troubleshooting includes a problem of the floor scrubber that assumes water is not being released by the water dispenser. To scrub floors, water is used to remove dirt and dust from floors. If you notice the problem during a cleaning procedure, you will not able to clean your floors at that moment. It needs to repair the whole system of the water releasing unit of the machine. 
The fixing of the situation is to fill the machine with water. Because it was never filled with water. If the machine has not sufficient water or is fully emptied, it will not clean your floors that come from dispensing water on the floor cleaning procedure.
Fill the water and test it to see whether it is working or not. If you see that the problem is still being persistent, there is likely a clogged hose or valve. Check out the water tank if any blockage for valve or hose.
Solution filters of a scrubber are commonly forgotten. Very often they are left unclean. As a result, they easily get clogged and do not work properly. A clogged filter will not pass water to floor cleaning procedures.
An easy fixing you can do by cleaning the blockage after an inspection for filters. If you see the filter is dirty, remove any dust-buildup with the stick and reconnect it to the floor scrubber. Once you have done everything carefully, the machine will start dispensing water again. If none of the tips and tricks does work, contact an authorized repair service for help.
Troubleshooting-3: Brush Deck Doesn’t Scrub
All equipment of an automatic floor scrubber will run on battery power. If any equipment can sense the weakness of battery power, it will restrict working for the session of floor scrubbing. However, to lower the brush deck to perform the scrubbing procedure, it needs to have sufficient battery power. In the sequence, if the battery signals down, the ability to lower the brush is disappeared. So it doesn’t work properly. 
Check the battery now. If it is found low or dead, get it changed to perform again.
Otherwise, if the battery signals of fully charged, but doesn’t work for an instant, this is clear that the brush deck is jammed or damaged. Call in an authorized technician for help.
Troubleshooting-4: Poor Scrubbing Results
Brushes or pads are the main equipment for the auto scrubbers to scrub the floor clean. If you think that your scrubber is giving poor results, the cause is the wrong pad or damaged pad for the scrubber.
There are different types of pads and brushes used for auto floor scrubbers. So it depends on the type of your floor finish that you require much for your home. 
Floor pads or brushes are not for a lifetime. They have limited time expectancy. So this is important to inspect any damage or excessive wear before starting the floor cleaning procedure.
Some floor types need to have some extreme pads while others will require some smooth and softer floor pads. Before getting demand to meet, check with an experienced technician to be firm that— what types of floor pads or brushes are appropriate for your floor finish.
Without taking much time for the damaged or worn pads, replace them as soon as possible. Even having the right pads or brushes, you may have poor scrubbing results. This is because of the wrong pad pressure setting on the system or improper chemical usages.
Automatic floor scrubbers have a different pad or brush pressure settings. So the situation is very important when you are going to deal with the different floor types. Sometimes it is critical for performing heavy restorative movements for a floor scrubber.
This is not all time you will be getting prospective results from your floor scrubber. It is essential to check then the pressure settings of the scrubber.
If all the well-settings of your floor scrubber are experiencing the scratched floors or a huge lack of finishing even after scrubbing, assume, your automatic floor scrubber might have encountered a combination of too much pressure and bad pad or brush. So reset the pad pressure setting.
Moreover, if it is not seen that the scrubber is not adequately dealing with the dirt and stains, this is obvious that you need to change the brush pressure setting. Correct pressure setting will allow you to adjust the chemical dilution and dispersing evenly on the floor during scrubbing.
More fixings you may experience when you will notice that your floors are not reaching the optimal outcome. This means you are applying wrong floor cleaning chemicals on the pad or brush. Cleaning chemicals are used to emulsify soil on the floors. The chemicals also allow scrubber for emulsified soil to easily squeegee the floor suckling the dirt and water from the floors.
To achieve a complete result, you need to select the right floor cleaner based on your floor types. The cleaning procedure is also a critical issue for the desired results from your floor scrubber.
Make sure the chemicals you typically use for your floor are compatible with the floor types or not. Remember, the concrete type floors will require am alkaline floor cleaner to deliver a prospective outcome. And, the waxed surface of the floor will require a pure neutral floor cleaner. If not sure, that you are using the right type of chemicals for your floor types, contact sales specialist to know the right directions for cleaning your floors. However, the above suggestion is the advanced floor machines troubleshooting for your convenience.
Troubleshooting-5: Down Runtime
In a longer period of my experience, I had to face the number of advance floor scrubber troubleshooting. Recently, I got a call from one of my customers who was having a problem with the floor scrubber. The runtime of the floor scrubber has been ridiculously down to 20 minutes to half an hour. He also ensures me he is doing everything all around very accurately. The floor scrubber was featured of 4, 6-volt wet cell batteries when he bought it. It also clarified me the water level for each cell was appropriately wonderful. Both the battery terminals and cables are clean. And, checking all other issues, he says that everything is looking good.
However, I have got the points that he had bought it for two years and a half. Now he is facing only one issue that the floor scrubber is not giving him much time as before. It runs for a very short time without having the job completed. I assume that the battery life is gone.
From his noted information, it is easily comprehensible that one or more cells of the batteries have been down to dysfunctional. But a question arises, within only two years and a half, how is it possible for a branded floor scrubber that has a battery issue? I asked him for the charging time of the batteries. He said politely that as he only uses it, three or four times a year when it needs to scrub or recoat the floors. One important thing he did—checked the water level and wiped down the entire scrubber including batteries every after using the floor scrubber.
I wish the issue was not a common problem that typically happens for floor scrubbers. But it seems to be more than I’m thinking it simply. Because you know that this is not wise while you are not getting batteries charged, it means it will not be steadily functional. Batteries need to be charged and consumed power routinely.
If you do not work with the battery-run equipment, and if you just let them sit idly, once, they will lose their ergonomic power and deteriorate on their own. Eventually, the will be out of function and difficult to recover the resilient condition as the new one. You also will not be able to get the batteries to charge at all. Because the batteries will not supply enough power to start the charger again.
An advance floor scrubber troubleshooting suggests that batteries need to charge and consume power following a particular routine to keep them steady at work. Most automatic floor scrubbers today usefully automatic chargers to charge batteries. Batteries remain well if they have power reading systems to charge them again if emptied. Conversely, if you get them idle for a few months or more, they may have not enough power in batteries to initiate the charging process after a long time passed.
In the moral of the battery life discussion, you will be prescribed to charge batteries regularly and consume the power to make a handsome turnover of power trading. Even if you are reluctant to use floor scrubber, do not leave it idle, charge batteries regularly. Based on your requirement, if the application of your floor scrubbing machine is periodic, you will never experience this type of problem with your machine. If you significantly maintain the batteries properly, it will go for several years of life out of a set of batteries that got from a new box packed.
However, except for battery issues, there are some more common problems users face and look for advance floor scrubbers troubleshooting. In many aspects, they are seen as easy to the eyes of the expert plumbers. So this is the place where you can have some troubleshooting for floor scrubbers. From onwards, I will be clarifying the most common issues and troubleshooting one after one. Until a finish of all, hope you will be reading them carefully and observe each point to capture in mind and take the preventive measure from happening it for your year-long floor scrubbers.
Troubleshooting-6: When a floor scrubber doesn’t suck dirty water up
This is one of the striking problems a user of a floor scrubber may encounter while getting not enough clean the floor after hours of floor cleaning. The causes of the situation depend on some issues that we will be writing them accordingly. And, lastly, a breakdown on the issue, will clarify the whole history of the scrubber problem.
For a floor scrubber machine, a Vac motor plays an important role to perform the cleaning process. So you need to know about—is the Vc motor running well? Make sure the Vac motor of the machine is running on but there is no activity of picking the dirty water up. Assume, some very simple reasons are there for the problem. 
Now go through a very common issue like squeegee of the floor scrubber. A squeegee is a scraping implement that integrates with a rubber-edged blade set underneath of scrubber to the cleaning process window. Notice if the Vac hose is attached to squeegee. If you find it everything ok, pull the Vac hose off the scrubber squeegee assembly. Now, look at the end of the hose. Can you see, is there plenty of suction made by the floor scrubber? Unfortunately, if you cannot see it happens, it seems that something happens with the hose that obstructs the suction capability of the scrubbing machine.
Now the perspective will lead you to clear the clog of the hose. You will able to simply fix it. Well, the reason for being clogged up the hose is the dust and dirt. During a cleaning process, some debris stream up towards the recovery tank of the scrubber. So every after use, it needs to checkup the recovery tank so that dust and debris cannot be stranded into the recovery tank. You can use a broom handle or things like that to clean up the clog of the Vac hose. You also cannot spare your checking inside the squeegee where it may have dust clogged that hampers your floor cleaning work as well.
At your more efforts, you need to check the drain hose for dirty water. Look carefully, is the drain cap remain secured to the hose? Because the drain hose allows suction to the recovery tank of the scrubber. If the drain cap is not secured to the hose, it will cause a little suction on the Vac hose.
Sometimes Vac hose can have cracks or holes. This is one of the very reasons for losing the suction of the whole system. Once, you have got it all everything, next walk through the Vac hose it is attached to the recovery tank. I found everything is going the way of the system, nothing is needed any longer. Or, you can replace spare Vac hose in hands.
One more reason that the suction of the scrubber can be worked out in the gaskets on the recovery lid. There are several aspects of the lid to get into the recovery tank. Vac lid is one of many problems. Notice the following picture of the gaps in the gasket where suction is seen being lost. 
Though some scrubbers have alternative ways to filter the air passing through the Vac motor. And, the air passing job can be done by the filter panel of floor scrubber. So give your attention to it and get everything right way.
Conclusion
If you use an electric or manual device at home, this is wise to have the ability to identify the problems and causes to handle the issues on your own. If you do not have the basics of the electric items like automatic floor scrubber, every issue will run you on for the help of professionals. Here, some advance floor scrubber troubleshooting will help you gather some basics that you need to know.
For an automatic floor scrubber, once you are knowledgeable about the basic issues, it will not require you to call in a professional repair. The maintenance will be easy and you will be concerned about the problems in using the scrubber as your own. You will be able to avoid a huge cost for maintenance purposes.
In this article, we have discussed all possible causes and troubleshoot them in a view to helping you so that with DIY knowledge can be a spearhead to fix the issues your own.
However, this is very much important to read them carefully and take steps to learn them well so that you become someone like a professional to handle the issues accrued in at home with several devices like this automatic floor scrubber machine. Hope you have got my points in your heart.
Leave a Reply