Leaks are an annoying problem that can happen with any water faucet. Luckily, they’re not difficult to fix if you know what to do. This article will teach you how to fix a leaky kitchen faucet with two handles. And, you will get it running like new again in no time.
If your sink is draining slowly or the water pressure seems low, check the handle on the faucet for leaks. If there are drops of water coming from underneath the handle when it’s turned off, then there is likely a leak somewhere in your system and it needs to be fixed.
THIS ARTICLE
Necessary Tools Required to Fix a Leaky Kitchen Faucet
Follow the following step-by-step guide to get relief from dripping water from a leaky kitchen faucet with two handles. However, Make sure you’ve got everything that will help complete your task before starting. You should have a dual flat head or Philips screwdriver, new washers, and an adjustable crescent wrench on hand but here are some other items to consider:
- ½ inch plumber tape such as Teflon tape
- Masking tape
- A piece of towel and
- Vaseline or petroleum jelly
Finding the leak first: You can find out if your water is leaking by looking at the dripping part. Touch it and see whether you feel cold or hot liquid coming off it. The first thing you need to do is locate the leak. There are a few different ways that can be accomplished depending on what type of fixture or system your kitchen faucet operates within. If there’s water pressure coming out but not very much at all but dripping, this could mean an Individual ankle Joint has gone bad and requires replacement.
You need to protect your sink: When working with your sink, it is important to protect the surface of it by using masking tape. By doing so, you will be able to prevent any damage from occurring and finish up without worrying about dropping anything into the drain. Use a towel inside for extra protection when handling large tools such as wrenches or sockets. Because the tools may bounce around without your concern. So Protecting the finish on your faucet is important to keep it looking new. Masking tape will also help you in this circumstance. So wrap it around tightly before adjusting pressure and turning the wrench counterclockwise until tight or loose.
Removing the handle of the faucet: If you can’t find the handle’s screw, there is probably a decorative cap hiding it. If so, look for turning knobs on top and levers that need lifting to remove them (the underside). Your flathead screwdriver makes an excellent lever when applying pressure carefully while prying off its protective cover with your fingers. Once uncovered—unscrewing underneath should give access enough space for our handy toolkit, then put these parts away safely out of reach from young children who might be tempted by curiosity.
Pulling the stem out: The handle is attached to a stem that has 6-sided nuts. Tighten these using your wrench in whichever direction you need to torque. Then unscrew them when they’re loose enough with fingers and pliers if necessary. Now, lift on the flex pipe at the base so you can pull out this stubby little thingy sticking straight down below there.
Now Fixing the Leak
Handle: The first step is to wrap the white plumber’s tape carefully around the threads where you took out your 6-sided wrench. Now screw it back in place taking care not to over tighten it. And, if that doesn’t work, just unscrew again, but this time use another nylon washer underneath for added support before putting everything together again.
Stem: When you’re putting on a new O-ring, make sure to use your fingers and squeeze it together. Then take another one with the same size of nylon washer that is lubricated by petroleum jelly before replacing it in place.
Faucet: The bottom of the faucet stem has a screw that holds in place a rubber washer. Undo this with your Phillips-head screwdriver, then replace it for an appropriate size and put it back together again.
Reassemble your faucet: You can fix most leaks in two-handled faucets by following these easy steps. Apply plumber’s tape around the base of the stem, insert it into the handle and wrap with insulation washers all-around before tightening the 6-sided nut onto the thread at the bottom using a wrench or hex key. Put all parts back together in correct order—screw goes on the bottom followed by o-rings or washer sets, etc. Screw the top piece back on the handle; if done correctly your leak should be fixed instantly.
Conclusion
You’re learning how to fix a leaky kitchen faucet with two handles. If you are looking for a more in-depth guide on fixing leaky kitchen faucets, then we can help. You will find that this article has given you some great tips to get the job done quickly and efficiently at home. When it comes to repairing a leaky kitchen faucet, there are two main types of handles that you need to know about. These are the single handle and the double handle.
However, the first thing you should do is turn off your water supply by turning both valves on either side of your sink counterclockwise until they stop moving (typically located near where the pipes enter). Once this has been done, locate where the screws holding down each type of handle connect with your fixture. Put one hand under hot running water while using your other hand’s thumb and index finger to grip around them tightly. So they don’t slip out when loosening or tightening their connection points. Now unscrew whichever type of screwdriver would be appropriate for that particular job. Moreover, the instruction above will help fix the problem. Read that well.
Related:
Leave a Reply